Search found 25 matches
- Wed May 14, 2014 9:53 pm
- Forum: Loaders/Backhoes
- Topic: 3c mk111 brakes
- Replies: 10
- Views: 5282
Re: 3c mk111 brakes
Some pics as promised it dose need a bit of work but should look a lot better with new cab
- Wed May 14, 2014 11:30 am
- Forum: Loaders/Backhoes
- Topic: 3c mk111 brakes
- Replies: 10
- Views: 5282
Re: 3c mk111 brakes
Lovely thanks for that, just it seems to lose a bit of water when stood up into sump or cylinder so I think liner issue so will rebuild at later date. On the brakes I seem to recall there being holes in the floor plate above the axle inline with the brake linkage threaded rod I guess this is the adj...
- Wed May 14, 2014 8:16 am
- Forum: Loaders/Backhoes
- Topic: 3c mk111 brakes
- Replies: 10
- Views: 5282
Re: 3c mk111 brakes
Thanks for that, that is really helpful. Is there any diagrams for the brake discs inside the axle as I'd quite like to strip it out just to make sure that everything is ok in there and the discs don't need replacing? Also from the machine serial number has anyone got any idea what engine it has? Is...
- Sun May 11, 2014 8:05 pm
- Forum: Loaders/Backhoes
- Topic: 3c mk111 brakes
- Replies: 10
- Views: 5282
Re: 3c mk111 brakes
So I spent a bit of time this afternoon digging into it and have found two very rusty break pipes and one master cylinder bout pumping atall and both slaves leaking. Has anyone got part numbers for seal kit for slave cylinders? then I can get sone cunifer and make up some new lines. Thanks
- Sun May 11, 2014 10:41 am
- Forum: Loaders/Backhoes
- Topic: 3c mk111 brakes
- Replies: 10
- Views: 5282
Re: 3c mk111 brakes
Thanks. It seems to hold brake fluid but no pressure on the pedal so I'm assuming master cylinder seals would be a good start. The machine number is 137786/5. I am going to take the floor out and strip and clean all the assemblies and linkages to check they are all ok. Where is the best place to get...
- Sat May 10, 2014 9:34 am
- Forum: Loaders/Backhoes
- Topic: 3c mk111 brakes
- Replies: 10
- Views: 5282
3c mk111 brakes
I have just had my new project jcb 3c mk111 1980 powertrain turn up yesterday and among the important jobs the brakes don't work at all I'm not sure we're to start as it has hydraulic system at the pedal and axle. Dose any one know where to get parts for master and slave cylinders as I imagine seals...
- Sun May 04, 2014 9:45 pm
- Forum: Loaders/Backhoes
- Topic: 3c mk3 cylinder liners
- Replies: 2
- Views: 2127
Re: 3c mk3 cylinder liners
Hi thanks for that are any special tools required to pull the liners out and then replace them and set heights of new liners?
- Sat May 03, 2014 9:00 am
- Forum: Loaders/Backhoes
- Topic: 3c mk3 cylinder liners
- Replies: 2
- Views: 2127
3c mk3 cylinder liners
Hi, I have just naught an old bit worse for wear 3c mk3 which is losing water when parked up either into cylinder or into sump. I'm assuming that this is a liner issue so I'm looking at rebuilding the engine and was wondering how easy the liners are to replace and set up or if I need special tools t...
- Mon Apr 28, 2014 10:50 pm
- Forum: Wanted
- Topic: JCB 3C or similar
- Replies: 5
- Views: 3466
Re: JCB 3C or similar
Found one now. Bit rougher than originally planned but works and has v5. Could do with a bit of engine work and a serious cab work. Will start a project post with pics once it arrives. One question dose anyone know where to get a replacement cab or anyone who could makes replacements or restores old...
- Mon Apr 21, 2014 9:08 am
- Forum: Wanted
- Topic: JCB 3C or similar
- Replies: 5
- Views: 3466
Re: JCB 3C or similar
I am based in bristol area. And ideally some where in the region of 3k. I wish I had not scrapped my other one a couple of years ago due to top pin on back actor being repaired but out of line resulting in bent ram.