Search found 18 matches
- Tue May 21, 2024 7:57 pm
- Forum: Loaders/Backhoes
- Topic: 1982 3CX Rear Window Frame Parts
- Replies: 20
- Views: 7030
- Flag:
Re: 1982 3CX Rear Window Frame Parts
Anyone??
- Tue May 14, 2024 5:39 pm
- Forum: Loaders/Backhoes
- Topic: 1982 3CX Rear Window Frame Parts
- Replies: 20
- Views: 7030
- Flag:
Re: 1982 3CX Rear Window Frame Parts
Digging out an old one here... any tips on how I remove the rear window? Mine needs a complete overhaul as the handle is no longer engaging the centre spring.
- Mon Jan 22, 2024 5:33 pm
- Forum: Loaders/Backhoes
- Topic: Grey cab 3cx Air breather stuck
- Replies: 0
- Views: 1780
- Flag:
Grey cab 3cx Air breather stuck
Hi all, Need to replace my exhaust but the breather is not budging. Clip is removed but years of a badly worn exhaust seem to have caked around the flanges. Apart from the obvious of repeated lubrication over a few days any words of advice to get the bugger off?
- Mon Jan 22, 2024 5:29 pm
- Forum: Loaders/Backhoes
- Topic: Jcb 3cx hydrolic oil change
- Replies: 6
- Views: 3040
- Flag:
Re: Jcb 3cx hydrolic oil change
Thanks guys haven't drained the oil yet as I want to have my new oil gaskets and whatever else I need on hand before I start. Hopefully we'll things open back up on Saturday ( Bank Holiday at the moment) I'll get oil and if my local dealer has cover plate gaskets I think I'll get them aswell. Will ...
- Thu Jan 18, 2024 2:33 pm
- Forum: Loaders/Backhoes
- Topic: Perkins phaser 1004 in 3cx running bad
- Replies: 38
- Views: 253540
- Flag:
Re: Perkins phaser 1004 in 3cx running bad
Valid points Gecko. How would I go about testing the compression ? As for the injector spray pattern.. What would have changed that though? It always starts, just chuggs like a steam train trying to get moving before it does.
- Wed Jan 17, 2024 3:08 pm
- Forum: Loaders/Backhoes
- Topic: Perkins phaser 1004 in 3cx running bad
- Replies: 38
- Views: 253540
- Flag:
Re: Perkins phaser 1004 in 3cx running bad
Thanks for the reply Agrimax. I replaced the lift pump with a new one. Made no difference. I completely drained the fuel tank & cleaned it internally with bicarbonate of soda & distilled vinegar then added an additional inline filter. Made no difference. Battery has been replaced too. Any ot...
- Tue Jan 16, 2024 1:46 pm
- Forum: Loaders/Backhoes
- Topic: Perkins phaser 1004 in 3cx running bad
- Replies: 38
- Views: 253540
- Flag:
Re: Perkins phaser 1004 in 3cx running bad
Those are coolant temperature sensors. One for the temp gauge,one for the temp warning light/buzzer. Can't remember exactly but think the one circled in red is for the gauge. The glow plug/heater,if fitted,would be on the inlet manifold. Would have a steel pipe and wire attached to it. Back,right h...
- Sun Jan 14, 2024 11:04 pm
- Forum: Loaders/Backhoes
- Topic: Perkins phaser 1004 in 3cx running bad
- Replies: 38
- Views: 253540
- Flag:
- Thu Jan 11, 2024 9:09 pm
- Forum: Loaders/Backhoes
- Topic: Perkins phaser 1004 in 3cx running bad
- Replies: 38
- Views: 253540
- Flag:
Re: Perkins phaser 1004 in 3cx running bad
....3cx and whilst it runs fine, it cranks for quite a while before it starts. This is only from a cold start. It starts easier when warm. . Have you checked the wiring to the pre-combustion heater on the top right hand side at the front of the engine? My 1988 has that wire present and I've never h...
- Thu Jan 11, 2024 8:58 pm
- Forum: Loaders/Backhoes
- Topic: Perkins phaser 1004 in 3cx running bad
- Replies: 38
- Views: 253540
- Flag:
Re: Perkins phaser 1004 in 3cx running bad
Can anyone tell me if this http://www.moteur-perkins.com/uploads/catalogue/lettre/notice/perkins-manual-al.pdf is the manual for the engine in my machine? A 1989 grey cab non turbo sitemaster. The 1004 in my '97 3CX does not look like the engine pictured in your manual. First thing - does your engi...