Search found 64 matches

by Land Rover
Mon May 07, 2018 5:47 pm
Forum: Loaders/Backhoes
Topic: Here's one i finished earlier
Replies: 5
Views: 272

Re: Here's one i finished earlier

Lovely stuff , very well done .
Looks brand new . :D
by Land Rover
Sat Jan 13, 2018 8:43 pm
Forum: Loaders/Backhoes
Topic: Rubber Seal Between Cab And Chassis
Replies: 2
Views: 259

Re: Rubber Seal Between Cab And Chassis

I have seen people recommend these guys before
http://phoenixtrim.co.uk/
They have a nice online catalogue , I see page 30 has flat rubber .
Looks like you would just make one up , punch holes and use some sealant on the corners .
Best of luck , I'm sure it won't be as easy as it looks :D
by Land Rover
Mon Jan 01, 2018 10:19 am
Forum: Loaders/Backhoes
Topic: 1988 JCB 3xc 4WD Grey Cab
Replies: 20
Views: 944

Re: 1988 JCB 3xc 4WD Grey Cab

Topkit , thanks for that . I haven't done too much more than fill in pot holes with planings , but I have done roughly similar with type 1 etc . I think my pile of planings has been left too long to scoop up easily , I'll maybe use the back actor to loosen them up a bit . I must also be a bit tight ...
by Land Rover
Sun Dec 31, 2017 9:57 am
Forum: Loaders/Backhoes
Topic: JCB 3CX grey cab head lining advice
Replies: 11
Views: 849

Re: JCB 3CX grey cab head lining advice

Sikaflex or something similar , it would never come back off though
You will get it in most boat places
https://www.ebay.co.uk/itm/Sikaflex-221 ... Swn9lXKKCp
by Land Rover
Sun Dec 31, 2017 9:53 am
Forum: Loaders/Backhoes
Topic: 1988 JCB 3xc 4WD Grey Cab
Replies: 20
Views: 944

Re: 1988 JCB 3xc 4WD Grey Cab

The gearstick is the same on mine too and it was on my old 2wd 3cx that i had a few years ago, i use mine aounfpd our place in 1st and mainly 2nd gear, i spead a load of road plannings today as the rain has made the place like a bog. Exhaust flap is going on mine next week, i also teated mine to a ...
by Land Rover
Sun Dec 31, 2017 8:23 am
Forum: Loaders/Backhoes
Topic: 1988 JCB 3xc 4WD Grey Cab
Replies: 20
Views: 944

Re: 1988 JCB 3xc 4WD Grey Cab

Yes the exhaust flap is defonetly on the list. And the way you describe the gear shift is exactly the same as my machine. What gear do you normally use most when working :insomnia: or what’s the best you think :thumbup: The exhaust flap helped mine from spewing water out when I start it after it's ...
by Land Rover
Sat Dec 30, 2017 8:31 am
Forum: Loaders/Backhoes
Topic: 1988 JCB 3xc 4WD Grey Cab
Replies: 20
Views: 944

Re: 1988 JCB 3xc 4WD Grey Cab

I have the same model . Looks very tidy . I see there are brackets holding the exhaust which I haven't seen before , not a bad idea . An exhaust flap might be an idea ?. The gear lever on mine is like stirring porridge , I just make sure I get 2nd and not 4th as the box starts to cook in 4th if you ...
by Land Rover
Tue Nov 28, 2017 12:23 pm
Forum: Loaders/Backhoes
Topic: Dipper Ram seal - 89 3cx
Replies: 7
Views: 547

Re: Dipper Ram seal - 89 3cx

You should find you can search this website and find the part number required .https://parts.jcb.com/ Or call / email Vicary Plant and give them your machine serial number http://www.vicaryplant.co.uk/ There must be dozens of JCB 3CX's in France , there seems to be an enquiry from someone based in F...
by Land Rover
Tue Aug 29, 2017 7:32 am
Forum: Misc earthmoving equipment
Topic: DIY Pond Dredger in Design Stage
Replies: 3
Views: 660

Re: DIY Pond Dredger in Design Stage

Bloody hell , sounds a good project .
If the silt is soft then it might bury the suction head into the silt and block it .
What would control the depth of dredge and rate of propulsion ?
by Land Rover
Mon Jul 17, 2017 2:31 pm
Forum: Loaders/Backhoes
Topic: JCB 3cx greycab tyre sizes
Replies: 3
Views: 446

Re: JCB 3cx greycab tyre sizes

Sorry , I was bored and googled the TZ markings , I think it's something to do with side protection and might be the model of Barum tyre .

Go to advanced search