freddyuk. L.E.S. engineering sell stuff for Petters, don't Know about the rocker oil feed pipe ,they might point you in right direction.
Norm
Search found 503 matches
- Mon Apr 29, 2024 11:58 pm
- Forum: Dumpers
- Topic: Parts for Petter engine - available??
- Replies: 3
- Views: 231
- Flag:
- Sat Mar 23, 2024 10:43 am
- Forum: Heavy Haulage
- Topic: Classic pictures Updated 06/05/2024
- Replies: 4290
- Views: 3054247
- Flag:
Re: Classic pictures Updated 20/03/2024
essexpete wrote:Jeremy Rowland wrote:essexpete wrote:mechman wrote:Hi all
Unusual bucket arrangement on the tracked loader, second last pic.
Norm.
Looking at the bucket teeth, it must load over?
It does look like it loads over, bet the operator had a sore neck after a shift on that.
Jeremy
Proper nasty but better than a shovel!
JUST.
- Thu Mar 21, 2024 10:31 am
- Forum: Heavy Haulage
- Topic: Classic pictures Updated 06/05/2024
- Replies: 4290
- Views: 3054247
- Flag:
Re: Classic pictures Updated 20/03/2024
Hi all
Unusual bucket arrangement on the tracked loader, second last pic.
Norm.
Unusual bucket arrangement on the tracked loader, second last pic.
Norm.
- Thu Feb 15, 2024 12:09 pm
- Forum: Loaders/Backhoes
- Topic: JCB 3cx
- Replies: 12
- Views: 22111
- Flag:
Re: JCB 3cx
Agrimax.
Gotcha.
Norm.
Gotcha.
Norm.
- Wed Feb 14, 2024 11:40 am
- Forum: Loaders/Backhoes
- Topic: JCB 3cx
- Replies: 12
- Views: 22111
- Flag:
Re: JCB 3cx
Pete. It's a different set up to the old 3Cs.( It would be) It has some kind of linkage at the bottom of the operating lever that slides a thingy in the valve block.It can be attached in several positions, don't know if that makes a difference. I'm going to try cracking a hose to determine the press...
- Wed Feb 14, 2024 1:46 am
- Forum: Loaders/Backhoes
- Topic: JCB 3cx
- Replies: 12
- Views: 22111
- Flag:
Re: JCB 3cx
Pic.
- Tue Feb 13, 2024 8:15 pm
- Forum: Loaders/Backhoes
- Topic: JCB 3cx
- Replies: 12
- Views: 22111
- Flag:
Re: JCB 3cx
Hi all. A little info required if possible. My JCB 3CX has a carriage that seems to be stuck in the middle of the rails. The operating lever was seized solid. I had to remove it from the machine to free it. Now that it's free it still doesn't work.Does the lever have to be pushed away from driver or...
- Sat Feb 03, 2024 9:19 pm
- Forum: Dumpers
- Topic: Petter PH1 - spill timing and rack position...
- Replies: 13
- Views: 1876
- Flag:
Re: Petter PH1 - spill timing and rack position...
Thanks Norm. Where am I measuring the 11/16 between? Is that the distance between the calibration mark and the spot face when the screw on the governor arm is just touching the end of the rack spindle? And is that with the governor fully forward (away from the flywheel) or fully back (towards the f...
- Sat Feb 03, 2024 8:29 pm
- Forum: Dumpers
- Topic: Petter PH1 - spill timing and rack position...
- Replies: 13
- Views: 1876
- Flag:
Re: Petter PH1 - spill timing and rack position...
Thanks Norm. Where am I measuring the 11/16 between? Is that the distance between the calibration mark and the spot face when the screw on the governor arm is just touching the end of the rack spindle? And is that with the governor fully forward (away from the flywheel) or fully back (towards the f...
- Sat Feb 03, 2024 11:18 am
- Forum: Dumpers
- Topic: Petter PH1 - spill timing and rack position...
- Replies: 13
- Views: 1876
- Flag:
Re: Petter PH1 - spill timing and rack position...
Fil .
I think the 13/16" is the no gap setting between the governor arm and the end of the rack spindle, then you go on to set the spill timing at the 1/2" setting. I'm pretty sure it's the governor setting that's at fault.
Norm.
I think the 13/16" is the no gap setting between the governor arm and the end of the rack spindle, then you go on to set the spill timing at the 1/2" setting. I'm pretty sure it's the governor setting that's at fault.
Norm.