Search found 5587 matches

by Jeremy Rowland
Wed Jan 16, 2019 8:50 am
Forum: Excavators
Topic: New owner of Hymac 580B
Replies: 71
Views: 12162

Re: New owner of Hymac 580B

Nice one Andy :thumbup: this does make a lot of sense especially with an old cast pad machine that tracks slowly, plus the trailer will come in useful to move other machines.

Jeremy
by Jeremy Rowland
Tue Jan 15, 2019 8:58 am
Forum: Loaders/Backhoes
Topic: jcb 3c mk 1
Replies: 2
Views: 100

Re: jcb 3c mk 1

Hi Shane and welcome :wave: sorry I can't give you much advice but I would start by getting the hydraulic fluid pressure to each side of the steering ram measured first, daft question here but is the ram 100% straight? Just a couple of ideas to run past you. :thumbup:

Jeremy
by Jeremy Rowland
Tue Jan 15, 2019 8:46 am
Forum: Dumpers
Topic: Thwaites nimbus
Replies: 5
Views: 250

Re: Thwaites nimbus

Hi Ken and welcome to the forum :wave: somebody on here should be able to give you the advice you are after; have a browse through the dumper threads you may find that the information id already on here, if I remember correctly I'm sure that somebody on here posted that Thwaites themselves are very ...
by Jeremy Rowland
Mon Jan 14, 2019 8:47 am
Forum: Wheel Loaders
Topic: Chaseside
Replies: 186
Views: 24355

Re: Chaseside

essexpete wrote:As an anorak I just need to point out that the 700 in these photos was a Torque Convertor model. The Bedford looked very tidy.


It's good that people do have anorak knowledge like this Pete :thumbup:

Jeremy
by Jeremy Rowland
Sun Jan 13, 2019 6:49 pm
Forum: Earthmoving models
Topic: Conrad Liebherr R9800 shovel?
Replies: 1
Views: 74

Re: Conrad Liebherr R9800 shovel?

Mark, sadly I don't think many manufacturers listen to what their customers ask for :thumbdown: however the upside is that from some of the models that I have recently seen (but not bought) do have some fantastic detail on them and are better than many of their predecessors, so there is always hope ...
by Jeremy Rowland
Sun Jan 13, 2019 6:42 pm
Forum: Heavy Haulage
Topic: Classic pictures Updated 13/01/2019
Replies: 3017
Views: 278172

Re: Classic pictures Updated 13/01/2019

Interesting collection of photos there Steve :thumbup: the first one is a 580C complete with two headed operator :lol: looks like a kid in the back of the cab just how I started out :thumbup: The Mk11 Atki Defender has a modified sleeper cab conversion more unusual on an eight legger :thumbup: and t...
by Jeremy Rowland
Sun Jan 13, 2019 6:35 pm
Forum: Wheel Loaders
Topic: Chaseside
Replies: 186
Views: 24355

Re: Chaseside

Thanks Pete I don't do Farcebook :thumbup:

Jeremy
by Jeremy Rowland
Thu Jan 10, 2019 8:51 am
Forum: Loaders/Backhoes
Topic: Artic Steer Backhoe Loaders
Replies: 3
Views: 294

Re: Artic Steer Backhoe Loaders

Pete I guess it depends on what application you are going to use the machine for; perhaps some of the smaller artic steer machines may be more manoeuvrable in tight situations but I guess there would be an added expense to these machines as well as its cheaper to make a steering axle as opposed to m...
by Jeremy Rowland
Sun Jan 06, 2019 10:30 pm
Forum: Heavy Haulage
Topic: Classic pictures Updated 13/01/2019
Replies: 3017
Views: 278172

Re: Classic pictures Updated 06/01/2019

Nice pics Steve :thumbup: some great hydraulic excavator pictures, the first one is rather rare a JCB 7 :o then Hymac 580C, 690, 580C, 480, 580C and a 580BT.

Jeremy
by Jeremy Rowland
Fri Dec 28, 2018 11:09 pm
Forum: Dumpers
Topic: Thwaites 4WD 3T Dumper Restore
Replies: 30
Views: 6843

Re: Thwaites 4WD 3T Dumper Restore

Hi Sean, it is very hard to see from that photograph because unless it's the camera angle the level plug on the diff casing looks higher than on the brake casings? What does it say in the manual?

Jeremy

Go to advanced search